Project Description

MB

FLAT FAN LANCE ATOMIZER

Water Flow Rate

0
min
0
max
0
min
0
max

Materials

Body: Brass
Tube: Brass
Tip: Brass, Ni-plated brass, AISI 3

Connection

Plug-in

Primary Spray Angle

From 30° to 130°

MB

FLAT FAN LANCE ATOMIZER

Water Flow Rate

0
min
0
max
0
min
0
max

Materials

Body: Brass
Tube: Brass
Tip: Brass, Ni-plated brass, AISI 3

Connection

Plug-in

Primary Spray Angle

From 30° to 130°

MB

FLAT FAN LANCE ATOMIZER

Water Flow Rate

0
min
0
max
0
min
0
max

Materials

Body: Brass
Tube: Brass
Tip: Brass, Ni-plated brass, AISI 3

Connection

Plug-in

Primary Spray Angle

From 30° to 130°

MB LANCE ATOMIZERS

In continuous casting, and in slab casting in particular, lance atomizers replace conventional compact atomizers, currently called block atomizers, where the atomizer body is equipped with an extension and the spray tip is located at the exit end of the extension. The reasons of this replacement are due either to the geometrical need to insert the spraying pipe between rolls, whose clearance is often very small and prevents the use of block atomizers, or to the convenience to position the feeding pipes far from the intensely heated area near the slabs.

Lance atomizers can be classified according to different parameters:
Atomizer’s body: the body where atomization is generated is matched by a plug-in connection to fluid feeding ducts, may have different shapes according to the model and may be casted or machined.
Geometry of the pipe: straight pipe, or bent type.
Connections of the pipe to the body: the extension pipe is welded onto the block body, or the extension pipe is screwed to the block body with a locknut.

CLJet deflection angledegDULiquid outlet diammRFFemale threadinch
DConventional orifice diammFFFlange outer diammRGMale threadinch
D1Smallest free inside diammGFlange center-hole diammSQSquare bar sizemm
DELiquid inlet diammH,H1HeightmmWWeightgr, kg
DFFlange sizeinchL,L1LengthmmWSWrench sizemm
DIAOutside diametermmNRNumber of orifices
DNFlange nominal sizemmQCQuickfit connection

PNR laboratory can test MB lance atomizers, in order to determine the water-air flow rate diagram at different working pressures. Here is an example of the graphic we can provide to our clients:

If the customer need it, we can determine the Sauter Mean Diameter (D32), very useful for problems of thermal and material exchange.

+39 0383 344611

NOTE: for all models, it’s available the ECO version, with reduced air consumption. For instance:

Pw = Water Pressure
Pa = Air Pressure

NOTE: for all models, it’s available the ECO version, with reduced air consumption. For instance:

Pw = Water Pressure
Pa = Air Pressure

Body

Tip

MB
Flat Fan Lance Atomizer

www.pnr.eu
[email protected]
+39 0383 344611

MB LANCE ATOMIZERS

In continuous casting, and in slab casting in particular, lance atomizers replace conventional compact atomizers, currently called block atomizers, where the atomizer body is equipped with an extension and the spray tip is located at the exit end of the extension. The reasons of this replacement are due either to the geometrical need to insert the spraying pipe between rolls, whose clearance is often very small and prevents the use of block atomizers, or to the convenience to position the feeding pipes far from the intensely heated area near the slabs.

Materials
Body: Brass
Tube: Brass
Tip: Brass, Ni-plated brass, AISI 3

Connection
Plug-in

Lance atomizers can be classified according to different parameters:
Atomizer’s body: the body where atomization is generated is matched by a plug-in connection to fluid feeding ducts, may have different shapes according to the model and may be casted or machined.
Geometry of the pipe: straight pipe, or bent type.
Connections of the pipe to the body: the extension pipe is welded onto the block body, or the extension pipe is screwed to the block body with a locknut.

PNR laboratory can test MB lance atomizers, in order to determine the water-air flow rate diagram at different working pressures. Here is an example of the graphic we can provide to our clients. If the customer need it, we can determine the Sauter Mean Diameter (D32), very useful for problems of thermal and material exchange.

NOTE: for all models, it’s available the ECO version, with reduced air consumption. For instance:

Pw = Water Pressure
Pa = Air Pressure

PNR Italia 27058 Voghera (PV) Italy – Via Gandini 2
Phone: +39 0383 344611 Fax: +39 0383 212489 E-mail: [email protected]