Project Description

MW 1/4″
CLASSIC ATOMIZER – Full Cone Spray

www.pnr.eu
[email protected]
+39 0383 344611

MATERIALS: AISI 303 s.s., 316L s.s., PVC, NP Brass

SET-UPS: Pressure principle – Internal mix – Full Cone spray – 1/4″

FULL CONE SPRAY
These single orifice set-ups produce narrow-angle, full cone shaped, atomized sprays with a spray angle of about 20°.More precise details on the spray dimensions are given in the table on the right side of the page.The spray length can reach from 2.500 to 9.000 mm depending upon the set-up type and operating conditions.

SET-UPS: Pressure principle – Internal mix – Wide Angle Full Cone spray  – 1/4″

FULL CONE SPRAY
These set-ups are designed to work with a liquid fed out of an ambient pressure container, either by liquid siphoning or by gravity head.Therefore the performance tables give the water flow rate for both suction head (blue background) and gravity head (white background).The approximate spray depending upon set-up type and operating conditions are given from the table.

SET-UPS: Siphon principle – Internal mix – Full Cone spray – 1/4″

FULL CONE SPRAY
These set-ups are designed to work with a liquid fed out of an ambient pressure container, either by liquid siphoning or by gravity head.Therefore the performance tables give the water flow rate for both suction head (blue background) and gravity head (white background).The approximate spray depending upon set-up type and operating conditions are given from the table to the right,

PNR Italia 27058 Voghera (PV) Italy – Via Gandini 2
Phone: +39 0383 344611 Fax: +39 0383 212489 E-mail: [email protected]

MW

CLASSIC ATOMIZER
Full Cone Spray

Flow Rate

Liquid flow rate (l/h): min = 0,50  max = 250
Air flow rate (Nl/min): min = 10,2 max = 495

Liquid flow rate (gph): min = 0,13  max = 66,1
Air flow rate (scfm): min = 0,36 max = 17,5

Materials

AISI 303 s.s., 316L s.s.
LUCITE®, PVC
Nickel Plated
More materials on request

MW

CLASSIC ATOMIZER
Full Cone Spray

Flow Rate

Liquid flow rate (l/h): min = 0,50  max = 250
Air flow rate (Nl/min): min = 10,2 max = 495

Liquid flow rate (gph): min = 0,13  max = 66,1
Air flow rate (scfm): min = 0,36 max = 17,5

Materials

AISI 303 s.s., 316L s.s.
LUCITE®, PVC
Nickel Plated
More materials on request

MW

CLASSIC ATOMIZER
Full Cone Spray

Flow Rate

Liquid flow rate (l/h): min = 0,50  max = 250
Air flow rate (Nl/min): min = 10,2 max = 495

Liquid flow rate (gph): min = 0,13  max = 66,1
Air flow rate (scfm): min = 0,36 max = 17,5

Materials

AISI 303 s.s., 316L s.s.
LUCITE®, PVC
Nickel Plated
More materials on request

MW Body Type “A”

MW Body Type “B”

MW Body Type “C”

MW Body Type “D”

      SET-UPS: Pressure principle – Internal mix – Full Cone spray – 1/4″

FULL CONE SPRAY
These single orifice set-ups produce narrow-angle, full cone shaped, atomized sprays with a spray angle of about 20°.More precise details on the spray dimensions are given in the table on the right side of the page.The spray length can reach from 2.500 to 9.000 mm depending upon the set-up type and operating conditions.

COMPLETE  CODE
To obtain the complete code for an atomizer, it is necessary to use the set-up code you have chosen from the performance table and complete it with the code for body and options as follows.

• Replace the first two letters in the set-up code (SU) with the code for the standard body (MW).
• Add the code for the material you require.
• Add the code for the required options, if any, and the code for thread type.

+39 0383 344611

      SET-UPS: Pressure principle – Internal mix – Wide Angle Full Cone spray – 1/4″

WIDE ANGLE FULL CONE SPRAY
These multi-orifice set-ups produce wide angle, full cone shaped, atomized sprays as a result from the combination of several narrow angle sprays.The resulting encompassed spray angle is about 60°and more precise details on the spray dimensions are given in the table on the right side of the page.The spray length can reach from 1.500 to 10.400 mm depending upon the set-up type and operating conditions.

COMPLETE  CODE
To obtain the complete code for an atomizer, it is necessary to use the set-up code you have chosen from the performance table and complete it with the code for body and options as follows.

• Replace the first two letters in the set-up code (SU) with the code for the standard body (MW).
• Add the code for the material you require.
• Add the code for the required options, if any, and the code for thread type.

+39 0383 344611

      SET-UPS: Siphon principle – Internal mix – Full Cone spray – 1/4″

FULL CONE SPRAY
These set-ups are designed to work with a liquid fed out of an ambient pressure container, either by liquid siphoning or by gravity head.Therefore the performance tables give the water flow rate for both suction head (blue background) and gravity head (white background).The approximate spray depending upon set-up type and operating conditions are given from the table to the right,

COMPLETE  CODE
To obtain the complete code for an atomizer, it is necessary to use the set-up code you have chosen from the performance table and complete it with the code for body and options as follows.

• Replace the first two letters in the set-up code (SU) with the code for the standard body (MW).
• Add the code for the material you require.
• Add the code for the required options, if any, and the code for thread type.

+39 0383 344611