Project Description

HW/AM

FLAT FAN NOZZLE

Flow Rate

0
min
0
max
0
min
0
max

Materials

Body: AISI 303 s.s.
Insert: Tungsten carbide

Thread specification

Welding nipple and locknut

HW/AM

FLAT FAN NOZZLE

Flow Rate

0
min
0
max
0
min
0
max

Materials

Body: AISI 303 s.s.
Insert: Tungsten carbide

Thread specification

Welding nipple and locknut

HW / AM

FLAT FAN NOZZLE

Flow Rate

0
min
0
max
0
min
0
max

Materials

Body: AISI 303 s.s.
Insert: Tungsten carbide

Thread specification

Welding nipple and locknut

HIGH IMPACT NOZZLES – MICRO SIZE

In some plants the centre-to-centre distance among descaling nozzles can be very narrow. In these cases the use of micro-descaling tips avoids the installation of nipples and nozzles or rings onto the spray manifold, which would be difficult, if not impossible, with standard nozzles.

CLJet deflection angledegDULiquid outlet diammRFFemale threadinch
DConventional orifice diammFFFlange outer diammRGMale threadinch
D1Smallest free inside diammGFlange center-hole diammSQSquare bar sizemm
DELiquid inlet diammH,H1HeightmmWWeightgr, kg
DFFlange sizeinchL,L1LengthmmWSWrench sizemm
DIAOutside diametermmNRNumber of orifices
DNFlange nominal sizemmQCQuickfit connection
CONTACT US NOW!

+39 0383 344611

ASSEMBLY PARTS

WELDING NIPPLES

ZWM 0035 B2

Micro descaling nozzles can be assembled on the ZWM 0035 B2 nipple, 35 mm. long. PNR can supply on request a series of different length. The precision machined nipple inlet port assures precise positioning of the nozzle flat fan jet to the specified offset angle value of 15 ° with regard to the manifold centre line.

FLOW STABILIZER

XHW MG20 T1

The flow stabilizer is a critical component for proper descaling, by reducing flow turbulence losses, a larger fraction of the water flow energy can be used for generating impact on the surface to be descaled. The design consists of a cylindrical brass body with a polished inner surface, housing a cast stainless steel flow stabilizer which straightens the liquid path to minimize turbulences.

LOCKNUTS

VAW MM18 B1

The sturdy design and the generous dimensions of this locknut give the maximum protection to the nozzle and the nipple thread.

 

 

GASKET

VDA 10A5 T3

The VDA 10A5 T3 round gasket provides proper assembly and secure seal between nozzle and nipple.

HW / AM
Flat Fan Nozzle

www.pnr.eu
info@pnr.it
+39 0383 344611

HIGH IMPACT NOZZLES – MICRO SIZE

In some plants the centre-to-centre distance among descaling nozzles can be very narrow. In these cases the use of micro-descaling tips avoids the installation of nipples and nozzles or rings onto the spray manifold, which would be difficult, if not impossible, with standard nozzles.

Materials
Body:
AISI 303 s.s.
Insert:
Tungsten carbide

Thread specification
Welding nipple and locknut

WELDING NIPPLES
Micro descaling nozzles can be assembled on the ZWM 0035 B2 nipple, 35 mm. long. PNR can supply on request a series of different length.  The precision machined nipple inlet port assures precise positioning of the nozzle flat fan jet to the specified offset angle value of 15 ° with regard to the manifold centre line.

FLOW STABILIZER
The flow stabilizer is a critical component for proper descaling, by reducing flow turbulence losses, a larger fraction of the water flow energy can be used for generating impact on the surface to be descaled. The design consists of a cylindrical brass body with a polished inner surface, housing a cast stainless steel flow stabilizer which straightens the liquid path to minimize turbulences.

LOCKNUT
The sturdy design and the generous dimensions of this locknut give the maximum protection to the nozzle and the nipple thread.

GASKET
The VDA 10A5 T3 round gasket provides proper assembly and secure seal between nozzle and nipple.

PNR Italia 27058 Voghera (PV) Italy – Via Gandini 2
Phone: +39 0383 344611 Fax: +39 0383 212489 E-mail: info@pnr.it